Tool Sharpening Doesn't Have To Be Mysterious

!9# Tool Sharpening Doesn't Have To Be Mysterious

[if ]

[endif]

Many woodworkers are intimidated by the very idea of sharpening their tools. There's often a fear of doing more harm than good. This task really isn't as difficult as it might seem. Approached with some patience, and armed with some back round information, it's really a matter of practicing. Knowing you really can't do irreversible harm makes it somewhat less intimidating.

With so many options available it becomes somewhat overwhelming trying to decide which sharpening device will provide the best results, with the least amount of difficulty. Since there are many different tools requiring a very sharp edge for woodworkers, the method chosen will need to be adaptable, or at least have accessories to provide versatility.

Some of the sharpening equipment on the market have a pretty steep price tag and once you start buying accessories for them, the cost can approach a thousand dollars, or more! The good news is there are many tools available, at reasonable prices that will provide an edge that will cut as intended.

While I do have and use the more expensive sharpening equipment, and the accessories, I rarely use it unless I have a number of tools needing some serious work. More often, it's a matter of touching up an edge, (unless someone used your finest chisel to open a paint can!). It happens.

Some of the least expensive methods can produce incredible results when used properly. Very often I use a small piece of M.D.F. , "charged" with diamond paste. This paste is available from a number of sources, and is sold in kits. These kits have several tubes of varying grits of the paste and small pieces of M.D.F. included in the box. It's important to wrap them with wax paper after use so as not to contaminate them with different grits.

In using this method, it's important not to push the chisel, as it will quickly destroy the M.D.F. My method consists of placing the chisel on the block, rocking it until I find the proper angle, and pulling it back across the block. Small circular or figure eight patterns are fine, provided vary light pressure is applied to the chisel, forcing it to dig in. Surprisingly, this inexpensive method will put a mirror finish on your edge, although it's not the fastest method available.

Another method of sharpening is using stones. I personally like water stones, and have a number of them as well. Again, it's important not to contaminate the grits from one stone to the next. Water stones do require flattening, as they are prone to wear. With a stone flattener, this process is very simple and quick.

Another very fast method of dressing an edge is to use a wood, leather, or cloth wheel that has been charged with a honing or polishing compound. These wheels can be used in a drill press, on a lathe or a grinder. Again, never have the edge in a position to dig into the wheel. Hold it so the spinning wheel is rubbing towards the edge and at the existing angle that's already on the tool. This method will bring back an edge very quickly.

I have wheels made from blanks of wood, usually Poplar, which have been charged with polishing compound and are permanently mounted to face plates. These wheels are turned to include coves and beads so I can polish the edge of turning tools. I've had some of these for close to twenty years, and used with care will last indefinitely. I also use these to dress or hone flat chisels as well with equally effective results.

Another inexpensive method is known as "Scary Sharp". This method is basically a piece of plate glass sprinkled with water and a sheet of wet / dry sandpaper laid onto the glass. The reason for the water on the glass is to "stick" the paper on so it doesn't slide around on you. Additional water is sprinkled onto the sandpaper to lubricate the surface and prevent the chisel from sticking to the paper and moving it. This system is also very good and will give you an edge that is hard to beat.

It's important to realize, you don't need to run out and buy the most expensive sharpening equipment to keep your tools sharp. It's far more important to learn the proper use of the system you choose.

Tool Sharpening Doesn't Have To Be Mysterious

Bissell 2x Decide Now Pyrex Lids Replacement Plastic Reviews Shopping Stash Tea

Dewalt DW718 Miter Saw Fence Alignment

!9# Dewalt DW718 Miter Saw Fence Alignment

[if ]

[endif]

With a tool so tough as Dewalt's DW718 12" double-bevel sliding compound miter saw, it is no mystery that the sucker is going to get a little kicked around. Of course, the regular abuses of jobsite life will wear on the tool and eventually it's going to require a bit of tinkering on your behalf. Don't fret though, said tinkering is generally simple with the right tools and a bit of patience.

It may surprise you to learn that the leading cause of inaccurate miter saw cuts is actually a misaligned or warped fence. As many awful things like kickback and sloppy cutting can result from a misaligned or otherwise off-kilter rip fence, your fence alignment and the fence alignment process are important parts of miter sawing and miter saw ownership; despite the seemingly elementary process of this procedure, it can make or break your cutting results. Additionally, because Dewalt's DW718 packs such a serious amount of punch, ensuring that your cuts are accurate and your materials are safe from error or kickback is all the more important. Be precise and be cautious.

So, to get down to business, using a framing square or straight-edge that is at least as long as your fence, press a piece of ultra thin paper (i.e. tracing paper or telephone book paper) against the fence (or straight-edge). The fence and square should sandwich the paper. Now, tug softly at the top of the paper. It should be tightly stuck between the fence and the square at all points from one end of the fence to the other. If at any point you can remove the paper from said contraption, you have a bow, a sway, or an imperfection in the fence that needs to be corrected.

To adjust the DW718's one piece fence, loosen the screws closest to the imperfection and remembering to not over-correct use a pry bar to gently force that bent fence straight. Maintain pressure on the pry bar and tighten the screws. Recheck this space to be sure the bow has completely straightened. Repeat the process until the paper can not be removed from any point on the fence. Additionally, and as with almost all things in life, this procedure is generally easier with four hands; if someone can help you, gratefully accept their offer and hold and push and pull and test and measure until your fence is perfectly straight. Additionally, and I reiterate, please be careful as you correct your fence; move it only in very small increments to avoid over-correcting any imperfections.

If you discover you need an extra hand aligning the fence on your DW718 miter saw, simply take the saw to a factory authorized Dewalt service center for adjustment.

Dewalt DW718 Miter Saw Fence Alignment

Car Amplifier Power Purchase Purchase Sharp Lc46d62u

DEWALT DW718 12-Inch Double-Bevel Slide Compound Miter Saw

!9# DEWALT DW718 12-Inch Double-Bevel Slide Compound Miter Saw

Rate : | Price : $429.99 | Post Date : Nov 09, 2011 02:00:58
Usually ships in 24 hours

Whether you're cutting baseboard or crown molding, the DEWALT 12-Inch Double-Bevel Sliding Compound Miter Saw provides quick, accurate cuts to complete the job. Thanks to a powerful 15 Amp motor, an easy-to-adjust cam-lock miter handle, convenient miter and bevel stops, and a tall fence for oversized moldings, this saw is ready for a range of crosscutting and miter-cutting applications. In addition, it comes with a durable carbide blade, a blade wrench, and a convenient dust bag.

12-Inch Double-Bevel Sliding Compound Miter Saw At a Glance: Powerful 15 amp motor delivers no-load speed of 3,600 rpm Adjustable stainless steel miter detent plate with 11 positive stops Tall, sliding fence for work with crown and base moldings Four hardened steel bevel stops on each side for versatility Two steel horizontal rails for blade travel Three-year limited warranty, one-year free service, and 90-day money-back guarantee

This miter saw features a 15 amp motor that delivers 3,600 rpm for a wide range of cutting jobs. View larger.

The saw's tall fence allows you to cut oversized molding. View larger.

Smart, Powerful Design for Quick, Accurate Cuts
The DEWALT double-bevel sliding compound miter saw's 12-inch blade is backed by a powerful and dependable 15 amp motor. Offering a no-load speed of 3,600 rpm, it makes quick work of cutting framing or molding, as well as other crosscutting and miter-cutting jobs.

This sturdy saw is designed to deliver precise cuts, allowing for the versatile setups required for miter applications. The precise miter system's adjustable stainless steel miter detent plate features 11 positive stops. An easy-to-adjust cam-lock miter handle delivers quick and accurate miter angles, and features a convenient detent override, which allows you to adjust the miter setting without the saw slipping into the miter detents. And the saw's big miter capacity--0 to 60 degrees to the left and 0 to 50 degrees to the right--adds versatility.

Tall Fencing and Compact Sliding Rails
The tall fence supports 6-5/8-inch crown molding nested vertically, as well as 6-1/2-inch base molding set against the fence. The fence slides out of the way easily when it's time to make bevel cuts. This saw stays compact thanks to its dual horizontal steel rails, which feature an innovative clamping mechanism and linear ball bearings for increased accuracy and durability.

Increased Bevel Capacity and Convenient Stops
This saw is designed to deliver quick, accurate bevel cuts. You can easily set up for bevel cuts that measure between 0 and 48 degrees to the left and to the right. This handy setup provides increased capacity for big jobs and allows you to flip the saw instead of the material. Plus, with hardened steel bevel stops at 0, 33.9, 45 and 48 degrees on both sides, it makes finding and setting the most common bevel angles a quick, easy process.

Ideal for a range of applications, the saw's unique fence design allows it to deliver clean, 45-degree bevel cuts through dimensional lumber measuring up to 2 by 12 inches. At 90-degrees, it can cross cut 2 by 16s.

Portable and Compatible with the DEWALT Laser and L.E.D. System
This lightweight compound miter saw weighs just 53 pounds and features a built-in carry handle, so you can move it around the jobsite easily and lift it comfortably when it comes time to stow the saw at the end of the day.

For additional accuracy and ease of use, this saw is compatible with a DEWALT DW7187 (sold separately) adjustable miter saw laser system (sold separately), which ensures that the cutting line is easy to see via a red laser line. An addition option is the DWS7085 (sold separately) which light the work surface and identifies the specific cut line.

This 12-inch double-bevel sliding compound miter saw also comes with a DEWALT warranty package that includes a three-year limited warranty, a one-year free service contract, and a 90-day money-back guarantee.

What's in the Box
DW718 DEWALT 12-Inch Double-Bevel Sliding Compound Miter Saw, carbide blade, dust bag, blade wrench, and vertical material clamp.

The adjustable stainless steel detent plate features 11 positive stops and rotates 90 degrees for a wide range of cuts.

• DEWALT DWX723 Heavy Duty Miter Saw Stand
• DEWALT DW7187 Adjustable Miter-Saw Laser System
• DEWALT DWS7085 Miter-Saw LED Work Light System
• DEWALT DW7231 Miter-Saw Workstation Tool Mounting Brackets
• DEWALT DW723 Miter Saw Stand

Catalog Playtex Baby Call Sharp Free Shipping

MD12-726TBC SLIDING COMPOUND MITER 12"x72T A.G.E SAW BLADE AMANA TOOL

!9# MD12-726TBC SLIDING COMPOUND MITER 12"x72T A.G.E SAW BLADE AMANA TOOL

Rate : | Price : | Post Date : Nov 03, 2011 09:05:41
Usually ships in 2-3 business days

Price B Grade Maple Syrup